A trader in Rotterdam once asked me for a price on "99% sodium bicarbonate". Three customers, one product, he thought. A bakery, a dairy feed mill, and a waste-to-energy plant. I asked him to send the three specifications. Two of them contained limits that the cheapest material on his list would fail, and neither limit had anything to do with the assay.
That is the first thing to get straight about sodium bicarbonate. The 99% figure is a titration result. It tells you how much acid the powder neutralises. It does not tell you what else is in the bag.
What "99%" actually measures
Sodium bicarbonate, NaHCO3, CAS 144-55-8, is a white crystalline powder. Assay is usually run by acid-base titration and reported as 99.0% or above on a dry basis. The number is real, but it is a single point on a much longer sheet.
The rest of the sheet is where grades separate. Chloride, sulfate, iron, water-insoluble matter, heavy metals, arsenic, moisture and particle size all change with the raw material and the crystallisation step. Two suppliers can both ship 99.2% material and still give you very different behaviour in a bakery or a scrubber.
Food grade is not just "feed grade with a certificate"
In the EU, food-grade sodium bicarbonate carries the additive number E500. In China the relevant standard is GB 1886.2 for food additive sodium bicarbonate. In the US, FCC monographs apply. A food-grade shipment should come with a batch COA that references the standard you are actually selling against, plus the food additive production licence behind the plant.
The functional job in baking is simple to describe and harder to control. Bicarbonate releases carbon dioxide when it meets acid and again when it is heated. The temperature window, the particle size and the way the powder disperses through the dough decide whether you get an even crumb or a tight core with large bubbles near the top.
Fine powder reacts fast and disperses well, but it dusts and cakes. A coarser cut flows better in a plant and dissolves slower in a cold mix. For dry blends that sit on a shelf, moisture pick-up is the enemy. A bag that gains a fraction of a percent of water will set into lumps, and the customer blames the formula.
Feed grade lives or dies on rumen chemistry
Dairy nutritionists use sodium bicarbonate as a buffer. The rumen runs acidic after a heavy concentrate meal, and bicarbonate helps hold pH inside the range where fibre digestion still works. The typical inclusion is often quoted around 100 to 200 grams per head per day, but the right number belongs to the nutritionist who knows the ration, the DCAD balance and the heat stress load.
What the feed mill needs from the supplier is different from what the bakery needs. Flow in the mixer, low dust, consistent particle size, and a chloride level that does not add to the dietary chloride load. If the material cakes in the silo, the weigh hopper will dose lumps and the mixer will not disperse them. If the particle size shifts between lots, the rumen response shifts with it.
Feed-grade material also has to fit the feed additive rules of the destination market. That means the right registration documents, not a food certificate with the word "feed" written on the envelope.
Flue gas scrubbing is a chemical engineering purchase
In flue gas treatment, sodium bicarbonate is injected dry or in a slurry to neutralise acidic gases such as sulfur dioxide and hydrogen chloride. Reactivity depends on surface area, particle size and how the powder disperses in the duct. A coarse, dense crystal that works fine in a bakery may be the wrong choice for a scrubber, and a very fine material that reacts quickly may be hard to handle and dusty.
The industrial buyer also cares about chloride and sulfate because they affect the spent sorbent and the disposal route. And the plant cares about moisture because a caked silo stops the injection system at the worst possible moment.
The physical numbers worth knowing
Sodium bicarbonate decomposes around 270 degrees C, releasing carbon dioxide and water and leaving sodium carbonate behind. That is why it works as a leavening agent and why it is not the right material for a process that runs hot before the reaction you want.
Solubility is roughly 9 grams per 100 millilitres of water at 20 degrees C. Bulk density usually sits between 0.9 and 1.2 grams per cubic centimetre depending on the crystal form and the sieve cut. Neither number is exotic, but both matter when you design a silo, a feeder or a dissolution tank.
What to put in the purchase specification
Start with the standard you are selling against. E500, GB 1886.2, FCC or the pharmacopoeia, whichever applies. Then add the things that actually break your process:
- Assay, with the method and the basis stated.
- Moisture, with a ceiling that matches your climate and your bag.
- Chloride, sulfate, iron and water-insoluble matter, each with a limit.
- Heavy metals and arsenic, against the food or feed standard.
- Particle size, expressed as a range or a sieve cut, not "fine powder".
- Bulk density and flow, if the material goes through a silo or a dosing screw.
- The packaging, because a 25 kg bag and a 1,000 kg jumbo bag behave differently in a humid warehouse.
A certificate that lists only assay and moisture is not a specification. It is a receipt.
Storage and the caking problem
Sodium bicarbonate is hygroscopic enough to cause trouble in a bad warehouse and stable enough to be boring in a good one. Keep it dry, keep it off the floor, and do not stack bags against a cold wall where condensation forms. A sealed liner matters more than the outer weave.
If you buy in jumbo bags, ask for a liner that can be closed again after partial use. If you buy pallets, ask for shrink wrap and a desiccant policy in the rainy season. These are not glamorous questions, but they decide whether the last 200 kg of a lot is usable.
A small trial that tells you more than a brochure
Bake a pound cake with the candidate material and a control. Keep the formula and the oven identical. Look at the crumb, the dome and the bottom crust. Then hold the powder in an open dish at 80% relative humidity for a week and see whether it still flows.
For feed, run a 20 kg mix and check for lumps at the mixer discharge and at the bagging line. For scrubber trials, ask for a particle size distribution and a reactivity curve, then test in a slipstream if you can.
None of this takes a week. It takes a few hours and it tells you which of the three grades you are actually buying.
Where our supply sits
Our Haihua sodium bicarbonate line ships food grade, feed grade and industrial grade from the same production base, with a lot COA and the relevant compliance documents. Assay is 99% or above, the material is white crystalline powder, and we can cut the particle size to the application instead of selling one grind to everybody.
I would rather lose a quote than sell a bakery the same sieve cut we send to a scrubber. The chemistry is the same. The purchase is not.
FAQ
Q1. Is sodium bicarbonate the same as baking soda?
A: Yes in everyday language. Baking soda is food-grade sodium bicarbonate. The difference between products is the purity, the particle size and the documentation, not the chemical name.
Q2. What does 99% purity mean on a COA?
A: It is an assay result, usually from an acid-base titration. It tells you how much bicarbonate is present. It does not cover chloride, sulfate, iron, heavy metals or particle size, which are often the numbers that decide whether the material works in your process.
Q3. What is E500?
A: E500 is the EU additive number for sodium bicarbonate. Food-grade material sold into the EU should be able to support that labelling with the right specification and paperwork.
Q4. Can I use food-grade sodium bicarbonate in feed?
A: Sometimes the chemistry is acceptable, but the paperwork is not interchangeable. Feed has its own additive rules and registration requirements. Buy the grade that matches the market you are selling into.
Q5. How much sodium bicarbonate goes into a dairy ration?
A: Common recommendations sit around 100 to 200 grams per head per day, but the correct figure depends on the ration, the DCAD balance and the heat stress level. That decision belongs to the nutritionist, not the silica supplier.
Q6. Why does my sodium bicarbonate cake in the bag?
A: Moisture pick-up. The powder is hygroscopic, and a small gain in water is enough to form bridges between crystals. Check the liner, the warehouse humidity and the stacking against cold walls.
Q7. What particle size should I buy for baking?
A: Fine powder disperses and reacts quickly, which suits many dry mixes. Coarser cuts flow better and dissolve slower. The right answer depends on your mixer, your dough temperature and how long the batter sits before baking.
Q8. What particle size works for flue gas scrubbing?
A: It depends on the injection system and the residence time in the duct. Finer particles react faster but can be harder to handle. Ask for a particle size distribution and test reactivity in a slipstream before you commit to a silo design.
Q9. At what temperature does sodium bicarbonate decompose?
A: Around 270 degrees C. It releases carbon dioxide and water and leaves sodium carbonate. That is useful in baking and in some industrial reactions, but it is a limit in processes that run hotter than the target reaction.
Q10. How soluble is sodium bicarbonate?
A: About 9 grams per 100 millilitres of water at 20 degrees C. Solubility rises with temperature, which matters when you design a dissolution tank or a slurry system.
Q11. What is the bulk density of sodium bicarbonate?
A: Typically 0.9 to 1.2 grams per cubic centimetre, depending on the crystal form and the sieve cut. Use the supplier's measured value for silo and feeder design, not a generic figure.
Q12. What documents should come with a shipment?
A: A lot-specific COA with test methods, a TDS, an MSDS, and the compliance documents for the market you are selling into. For food and feed, that includes the production licence and the additive registration where applicable.